Description Product description Lubricant distribution Due to the special lubricant distribution construction, lubrication primarily takes place where it is needed: directly on the running tracks and the top surface of the Ball Guide Rail. 1 Top surface of the ball guide rail 2 Running tracks of the ball bearing guide 3 Oil tank 4 Seals Front lube unit R1619 2. 10 Material: special plastic The front lube units R1619 2. 10 are left empty at the factory. Possible travel distance with front lube units Previous travel distance s A With oil lubrication to 500 km B With grease lubrication to 1000 km Possible travel distance s C With front lube units to 10,000 km Front lube unit R1619 2. 00 Material: special plastic The front lube units R1619 .2. 00 are already filled with oil (Mobil SHC 639) and can be mounted after basic lubrication of the Ball Runner Block. Compare oil consumption for size 25 Front lube units Amount of lubricant oil per lubrication cycle Travel distance s Lubricant oil consumption absolute Lubricant oil consumption in comparison cm³ km cm³/km % without 1,2 20 0,06 100,00 with 5,2 5000 0,00104 1,73 Size 15 20 25 possible travel distance s with front lube units km 10000 Technical data General technical data Size Part number Oil Mass cm³ g 15 R161912500 1 15 20 R161982500 2.2 20 R161982600 1) 1.8 25 R161922500 2.6 25 R161922600 1) 2.5 1) For Ball Runner Blocks F.N (flanged ... low profile) and S.N (slimline ... low profile) Dimensions Dimensions Size 15 20 25 Part number R161912500 R161982500 R161982600 1) R161922500 R161922600 1) A4 mm 31.8 43 41 47 B3 mm 11.5 12.5 13 E8 mm 24.55 32.5 30.5 38.3 E9 mm 6.7 2) 7.3 2) 5.6 2) 11.5 2) 8.5 2) E9 2) 3) mm 10.7 - 15.5 - H mm 24 30 28 36 33 H 3) mm 28 - 40 - H3 2) mm 19.4 24.9 22.9 29.3 26.3 H3 2) 3) mm 23.4 - 33.3 - K2 mm 5 - 5 K3 2) mm 3.35 3.7 3.1 5.5 4.1 K3 2) 3) mm 7.35 - 9.5 - K4 2) mm 3.35 3.7 3.1 5.5 4.1 K4 2) 3) mm 7.35 - 9.5 - S12 M3 - M6 M3 S13 M3 M6 M3 1) For Ball Runner Blocks F.N (flanged ... low profile) and S.N (slimline ... low profile) 2) Based on the mounting face of the ball runner block 3) For ball runner blocks S.H (slimline ... high) a) Size 65 Mounting Prior to assembling the front lube units, initial lubrication of the Ball Runner Blocks with grease lubricant is required! See Ball Rail Systems - General technical notes and information, chapter "Maintenance". Assembly of front lube units – note for mounting The parts required for mounting are included (coated screws, seal and lube nipple). In each case, mount a front lube unit (Picture, Pos.3) on each side of the Ball Runner Block! Do not pull the Ball Runner Block out of the Ball Guide Rail! Ball Runner Block up to size 45: The enclosed lubrication pin (2) must be installed between the lube plate and the Ball Runner Block! (It contains a lube port.) Remove the set screws (1). Screw in lubrication pin (2). Slide on front lube units (3). Insert O-rings (5) between Ball Runner Block and front lube units. Tighten screws (4)
Бесплатная доставка по РФ при заказе от 50 000 р.
Компания ООО «Индатэк» работает с юридическими лицами по всей территории России. Каждый день мы осуществляем доставку заказов от Калининграда до Владивостока. Вместе с отгруженным товаром, клиент получает бухгалтерские и гарантийные документы на 12 месяцев. По желанию, вы можете продлить срок гарантии.
