Description Product description Structure and attachments Motor attachment – direct attachment with i = 1 The motor is attached directly to the compact module’s drive end enclosure via a motor mount. Motor attachment – with gear The planetary gearbox is attached by a mount. The mount serves to fasten the gearbox to the CRK and as a closed housing. Due to the connection without coupling, the drive torque is transferred to the drive shaft of the Compact Module with minimal torsional deflection. Available gear ratios: i = 3 (for CKR-145 and CKR-200), i = 5, i = 10 Structural design 1 Drive end enclosure 2 Frame 3 Belt drive 4 Carriage 5 Non-drive end enclosure Additional components 6 Magnetic sensor 7 Mounting duct 8 Socket/plug 9 Connection plate 10 Flanged type 11 Planetary gearbox 12 Motor Attachments Planetary gearbox with various gear ratios Maintenance-free servo motors with selectable brake and attached feedback Switches (magnetic sensors), switch activation without additional switch flag Socket and plug Mounting duct made of aluminum for sensors Design/options for guideway (frame), carriages, connection plates, see section “Dimensions” 1) Guideway (frame) 2) Carriages 3) Connection plates Lubrication versions Lube version LSS, LPG Grease lubrication with manual grease gun via frame, carriage or via connection plate 1) Connection plates Notes: LSS: Initial lubrication by Bosch Rexroth Relubrication using manual grease gun LPG: Ball Rail System and Ball Screw Assembly only with corrosion prevention Relubrication using manual grease gun Basic lubrication required Technical data Suitable loads Regarding the desired service life, loads for Fmgw, Fmbsshould not exceed around 20 % of the dynamic characteristic values (Cgw, Cbs). See Chapter "Project planning notes", document "Calculation". Do not exceed the technical data for the Linear Motion System. Note on dynamic load capacities and moments (see the table) Determination of the dynamic load ratings and moments is based on a total travel of 100,000 m. Often only 50,000 m are actually stipulated. For comparison: Multiply values C , M t and M L from the table by 1.26. 1) Applicable to CKK-110, -145, -200 with Resist cover Note: Observe the document "Calculation" in the section "Project planning notes". Load capacities and moments Size CKR-070 Lca without connection plate 1) mm 80 108 With connection plate 2) mm 60 95 Cgw N 2360 3830 ly cm⁴ 8.5 lz cm⁴ 55.1 Mt Nm 47 77 ML Nm 7 94 Mx max Nm 47 77 My max Nm 7 94 Mz max Nm 7 51 Fy max N 1270 2070 Fz1 max N 2360 3830 Fz2 max N 2360 3830 Z1 without connection plate mm 20 With connection plate mm 32.5 1) In the carriage design “without connection plate” the carriage length Lca corresponds to the length of the clamping surface. 2) The connection plate is mounted on the carriage design “without connection plate.” For the design with connection plate, the carriage length Lca corresponds to the length of the connection plate. Note: Observe the document "Calcul
Бесплатная доставка по РФ при заказе от 50 000 р.
Компания ООО «Индатэк» работает с юридическими лицами по всей территории России. Каждый день мы осуществляем доставку заказов от Калининграда до Владивостока. Вместе с отгруженным товаром, клиент получает бухгалтерские и гарантийные документы на 12 месяцев. По желанию, вы можете продлить срок гарантии.
