Description Front lube units suitable for RSHP Roller Runner Blocks and generation 1 Roller Runner Blocks For travel up to 5,000 km without relubrication Roller runner block only needs initial lubrication with grease Front lube units on both sides of the roller runner block Low lubricant loss Features Reduced oil consumption No lubrication lines Front lube unit can be refilled using the lube nipple on the end-face or at the side. Size 25: Lube connection on the end-face of the front lube unit is suitable for the grease lubrication of the Roller Runner Block. For this purpose, a lube pin is attached. For a detailed instruction for mounting with size 25, please refer to the Roller Rail System instruction. Product description Lubricant distribution Due to the special lubricant distribution construction, lubrication occurs primarily where it is needed: directly on the running tracks and the top surfaces of the roller guide rails. 1 Top surfaces of the roller guide rails 2 Running tracks of the roller rail system 3 Oil tank 4 Front seals Technical data General technical data Size Oil maximum operating temperature Mass cm³ °C g 25 2.6 + 60 24 35 8.3 46 45 13.8 88 55 22.8 122 65 47.6 225 Dimensions a) Size 65 Dimensions Size 25 35 45 55 65 A4 mm 44 64 78 91.5 119 B5 mm 13 16.5 18.5 20.3 21 B6 mm 15.5 19 21.8 24.3 E8 mm 33.4 50.3 62.9 74.2 35 E8.2 mm - 106 E9 1) mm 8.4 13.1 16.7 18.85 9.3 E9 2) mm 12.4 20.1 26.75 28.95 - E9.2 mm - 55 H 1) mm 36 48 60 70 90 H 2) mm 40 55 70 80 - H3 mm 29.2 40 50 56.3 74.8 H4 1) mm 0.5 0.75 H4 2) mm 4.5 7.75 10.75 - N8 1) mm 5 6.25 7.25 8.25 8.55 N8 2) mm 9 13.25 17.25 18.25 - N9 mm - 5.5 7.5 9 8.5 S8 M6 S9 - M6 1) Dimension with regard to mounting surface of roller runner block for a standard higher version 2) Dimension with regard to mounting surface of roller runner block for a higher version Mounting Prior to assembling the front lube units, an initial lubrication of the roller runner blocks with grease lubricant is required! See Roller Rail Systems - General technical notes and information, chapter "Maintenance". Assembly of front lube units The coated screws required for attachment additional end seals are supplied along with the unit. In each case, mount a front lube unit (1) on both sides of the roller runner block! Do not remove the roller runner block from the rail! Slide on the front lube units (1) and end seals (2) and align them on the roller runner block. Tighten screws (3) with tightening torque MA (see table). Maximum tightening torque MA Size Pos. 3 Tightening torque MA in Nm 25 M3 x 15 0,7 35 M3 x 22 0,7 45 M4 x 25 1,0 55 M5 x 30 1,3 65 M4 x 30 1,0 Notes The coated screws required for attachment on the roller runner block, additional end seals and lube nipples are supplied along with the unit. The front lube units are already filled with oil (Mobil SHC 639) and can be mounted immediately after basic lubrication of the roller runner blocks. Maintenance Lubrication intervals for roller runner blocks with fr
Бесплатная доставка по РФ при заказе от 50 000 р.
Компания ООО «Индатэк» работает с юридическими лицами по всей территории России. Каждый день мы осуществляем доставку заказов от Калининграда до Владивостока. Вместе с отгруженным товаром, клиент получает бухгалтерские и гарантийные документы на 12 месяцев. По желанию, вы можете продлить срок гарантии.
